How do you remove and install a tie-rod end on Lexus RX330?

Before removing the tie-rod, unscrew the wheel lug nuts, lift the front end of the car, put on jackstands, secure the rear wheels, engage the parking brake and then take off the front wheel. Subsequently, using the locking pliers or a wrench, loosen the jam nut sufficiently in order to compare the present position of the tie-rod with the end of the new, installed tie-rod end threaded for the same turns. When you can do this from the steering knuckle arm use a puller to remove the nut that will help you to separate the tie rod, remove the cotter pin and loosen the nut on the tie rod end stud closest to the centre of the vehicle. Disconnect the tie-rod end from the tie rod. For installation, slide the tie-rod end into the position marked and pass the threaded stud through the steering knuckle arm; then tighten the jam nut. Screw the castle nut on to the stud and tighten to the recommend torque. Last but not the least, place the wheel properly and tighten the lug nuts in the right manner that is to the recommended torque, then lower the car, then check the alignment by a dealer service department or an alignment shop.

Genuine Lexus RX330 Tie Rod End

Steering Rod End

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Tie Rod Ends found

View related parts
Lexus RX330 End Sub-Assy, Steering Rack
Part Number: 45503-49125
$187.69 MSRP: $253.81
You Save: $66.12 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Replaced by: 45503-09270
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2004-2006 Lexus RX330 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU38L-AWAGKA
View related parts
Lexus RX330 End Sub-Assy, Steering Rack
Part Number: 45503-09270
$186.16 MSRP: $253.81
You Save: $67.65 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Inner Tie Rod
- Replaces: 45503-49125
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2004-2006 Lexus RX330 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; GSU30L-AWAGKA, 3MZFE; GSU30L-CWAGKA, GSU35L-AWAGKA, GSU35L-CWAGKA, MCU33L-AWAGKA, MCU33L-CWAGKA, MCU38L-AWAGKA, MCU38L-CWAGKA
View related parts
Lexus RX330 Rod Assy, Tie, RH
Part Number: 45460-29435
$81.36 MSRP: $108.26
You Save: $26.90 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod Assy, Tie, LH
- Replaced by: 45460-09060
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2004-2006 Lexus RX330 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU38L-AWAGKA

Lexus RX330 Tie Rod End

The Lexus RX330 Tie Rod End serves as the essential link that converts the input of a steering wheel into the exact movement of the wheel, allowing drivers to point the SUV in the direction they desire. Sitting at either end of the steering rack in the RX330, each Tie Rod End connects the steering rack to the steering knuckle, and each Tie Rod End takes on the push and pull of the pinion gear to help the wheels swivel smoothly and remain on course. Regular inspection of the Tie Rod End on any Lexus RX330 helps catch wear early and keeps handling tight. The assembly comes in two forms, inner and outer Tie Rod End; the inner threads into the rack for strength and the outer uses a ball and socket joint that allows the suspension to rise and fall without upsetting steering accuracy. All Lexus RX330 models rely on a rack and pinion unit assisted by hydraulic power steering, which means the Tie Rod End must handle both driver input and the boost delivered by pressurized fluid. Over time, road shock and exposure can loosen joints, creating play that manifests itself in wandering or uneven tire wear that signals to drivers of every Lexus that replacement is needed to restore solid steering feel and factory alignment.

Should you need to purchase new auto parts for your vehicle, we strongly suggest you consider the genuine Lexus RX330 Tie Rod End available on LexusPartsNow.com. Our OEM Lexus RX330 Tie Rod End come with the reassurance of the manufacturer's warranty, a hassle-free return policy, and speedy delivery service, all at affordable prices online. Feel free to shop with confidence!

Lexus RX330 Tie Rod End Parts Questions & Experts Answers

Rod Assy, Tie, RH
45460-29435
Q: How do you remove and install a tie-rod end on Lexus RX330?
A:
Before removing the tie-rod, unscrew the wheel lug nuts, lift the front end of the car, put on jackstands, secure the rear wheels, engage the parking brake and then take off the front wheel. Subsequently, using the locking pliers or a wrench, loosen the jam nut sufficiently in order to compare the present position of the tie-rod with the end of the new, installed tie-rod end threaded for the same turns. When you can do this from the steering knuckle arm use a puller to remove the nut that will help you to separate the tie rod, remove the cotter pin and loosen the nut on the tie rod end stud closest to the centre of the vehicle. Disconnect the tie-rod end from the tie rod. For installation, slide the tie-rod end into the position marked and pass the threaded stud through the steering knuckle arm; then tighten the jam nut. Screw the castle nut on to the stud and tighten to the recommend torque. Last but not the least, place the wheel properly and tighten the lug nuts in the right manner that is to the recommended torque, then lower the car, then check the alignment by a dealer service department or an alignment shop.