Lexus 99132-12050 Bulb

For Front Park/Turn Signal Light removal, start by removing the plastic pin or screw securing the top of the housing, then pull the sidelight housing outward to access the bulbs. Rotate the bulb holder counterclockwise and remove the bulb. Reinstallation is the reverse of removal.For Rear Tail Light/Brake Light/Turn Signal removal, body-mounted lights on Avalon models require lens detachment via two screws, while on Camry and Solara models, pull back the trunk lining to access the bulbs. Rotate the bulb holders counterclockwise and pull out the bulbs. Access trunk-lid bulbs by pulling down inspection covers. Installation is the reverse of removal.For License Plate Light removal, with the trunk liner removed, take out the license plate bulb sockets and replace the bulbs. Reinstallation is the reverse of removal.For High-Mounted Brake Light removal, release plastic clips under the rear seat package shelf in the trunk, then pull the housing up from inside the vehicle. Twist the bulb holder counterclockwise and remove the bulb. Reinstallation is the reverse of removal.For Instrument Cluster Removal, access the instrument cluster illumination bulbs by removing and replacing them from the rear of the cluster. Rotate the bulb counterclockwise to remove it. Reinstallation is the reverse of removal.For Interior Light Removal, pry off the interior lens, then detach the bulb from the terminals. Be cautious when prying to avoid shattering the bulb glass. Reinstallation is the reverse of removal.

To get to the front park/turn signal lights on the ES350, lift up the headlight assembly and turn the bulb holder clockwise to take out the bulb when ready to install them back, performing the reverse motion for removal. To reach the taillight, brake light, and turn signal bulbs, lift the trunk cover, turn the bulb holders counterclockwise to release them, then reinstall the holders in the exact same direction. To change the high brake light above the window, remove the angle by your back seat, pull the bulb from its slot by turning it counterclockwise, then pull the bulb straight out, reversal for installation. To replace instrument panel lightbulbs, detach the instrument panel, then rotate light bulbs counterclockwise to remove them before putting them back in from the same side. The interior light requires you to take off the lens cover, disconnect the bulb from its terminal contacts, and put everything back in the opposite direction. You can fix the license plate light by following these steps: press the release clip, move the light housing inwards, turn it, twist the bulb holder tail counterclockwise to get a new bulb, then put everything back in the exact opposite order. If you need to change the fog light bulb, first lift up your car, take out its front wheels and fender covers, and turn the bulb holder counterclockwise to pull it from the light housing. To replace the side turn signal light on ES350 models, carefully peel off the cover on top of the wing mirror, take out the mounting screws, unhook the light mount, unscrew the bulb counterclockwise, put it back in place by turning it clockwise.

All exterior light bulbs for 2008 or older Highlanders and 2009 or earlier Lexus vehicles include front signal bulbs and side light bulbs inside the headlight housing. When your Highlander or Lexus has turn signal lights below their side mirrors, take the mirror cover off carefully, disconnect the electrical wire, and unclip the light housing like a kit-you must replace the whole unit. You need to do three steps to swap out the front turn signal/parking and side marker light bulb. First, take out the headlight housing, then grasp the bulb holder and rotate it counter-clockwise to remove it, then pull it free. To remove the bulb, press it into the holder, rotate it anti-clockwise until it comes loose, and pull the bulb out. Reassembly is simply reversing this process. To remove fog lamp bulbs, raise the front of your vehicle, disconnect the electrical connector, turn the bulb holder to the left, and pull it out. Unscrew the panel inside the boot to locate and remove the back brake, tail, turn signal, and brake backup light bulbs. To change lamp bulbs, first rotate the bulb holder counterclockwise, pull it straight out, and then pull the bulb out of its holder. Installation works in the opposite direction. To get at the taillight housing, start by disconnecting its wired connections inside the car. Find and loosen the housing nuts there and then continue outside where you free the housing holding screws so you can take it off the entire rear bumper. To fix the lift gate taillight housing, first take off the trim panels. Pull the bulb holder counterclockwise and put it back into place. Replace the bulb when done. Disconnect the power connections, unscrew the housing nuts, and carefully detach the lift gate housing from behind. Keep track of the exterior clip when you do this. To change a license plate light bulb, unscrew the housing screws and pull off the housing. Then, pull the bulb straight out. Installation follows the same steps in reverse order. To access the bulb for your interior lights (map reading and dome), pop off the mushroom-shaped tip of the housing, grip the bulb firmly, and pull straight down from the metal clips to disconnect. Reassembling the bulb is the same, but in reverse.

Front turn signal, parking and side marker exterior light bulbs are sometimes referred to as light bulbs in the headlight housing. For the models with turn signal lights beneath the side view mirrors, carefully remove the mirror cover, disconnect the electrical connection and also unclip the plastic light assembly wherein the turn signal light assembly has to be replaced in its entirety. To cancel the front turn signal/parking and side marker light bulb, the headlight housing has to be removed then the bulb holder which must be turned counterclockwise and pulled out. To replace the bulb the following procedure is followed: to insert the thin end of the bulb into the holder, twist it anti-clockwise and then pull it out, whereas to put the bulb replace the above procedure in reverse. To replace fog lamp bulbs lift the front of the vehicle on jackstands, disconnect this connector and turning the bulb holder anti-clockwise. Note that for the 2010 and other subsequent model years, halogen bulbs can overheat from skin oil. This center high-mounted brake light bulb on 2009 and models earlier is reached by opening the rear hatch, then the trim piece and then disconnect the electrical connector and finally, you twist the bulb holder in a clockwise direction. For 2009 and later models, the assembly is replaced as a unit, if required for service or repair work. For replacing turn signal, brake, rear brake/tail and back-up lighting bulbs in the same models 2008 and earlier-the rear hatch must be opened and the access panel removed to reach the bulbs. For the models of 2008-2013 Highlander and 2010-2013 the bulbs can be accessed after the fasteners of the rear interior trim panels are removed. To get to the taillight housing one has to disconnect the electrical connector, then the nuts inside the vehicle, followed by the rear bumper cover and exterior retaining screw. For 2014 and later models, turn the lift gate handle to open it, undo the retaining screws and pull of the taillight housing with a note that for Lexus models one has to pry out the trim panel covering the screws. License plate light bulbs are replaced by unscrewing the housing and removing the bulb by pulling it straight by its base. A few of the interior lights, such as the map reading and dome lights are done by first accessing the lens, then pulling the bulb straight out of the terminal clips, and installation is done in a similar manner as the removal process.

90981-15021 & 99132-12050