How to remove and install a fuel pump and Fuel Level Sensor on Lexus RX330?

Remove the rear seat. Pull the fuel pump/sending unit floor service hole cover off gently with a screwdriver. Lower fuel pressure and unscrew the fuel tank lid to empty. Twist and remove the fuel pump electricity wire connection by pulling up on the release button at its base, using pliers if you need to. Take off the black ground wire from the power battery. Take off the top fuel-supply line by removing the clip, pulling up, and checking the O-ring for damage before securing a replacement. For vehicles made before 2007, remove bolts holding the fuel pump and fuel level sensor assembly to its housing. Grasp the fuel pump/Fuel Level Sensor assembly from the fuel tank, with gentle tilting, to avoid hurting the fuel inlet strainer and sending unit float, loosening and moving the spring-type hose holder so you can disconnect the hose. First look at the strainer connected to the fuel pump's intake. Clean it with solvent and a brush if it's dirty. Get a new strainer when needed. Undoing the installation is just the reverse of undoing it.

Genuine Lexus RX330 Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Fuel Level Sensors found

View related parts
Lexus RX330 Fuel Sender Gage Assembly
Part Number: 83320-0E010
$100.85 MSRP: $136.38
You Save: $35.53 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gage Assy, Fuel Sender; Fuel Gauge Sending Unit
- Replaces: 83320-48031
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2004-2006 Lexus RX330 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; GSU30L-AWAGKA, 3MZFE; GSU30L-CWAGKA, GSU35L-AWAGKA, GSU35L-CWAGKA, MCU33L-AWAGKA, MCU33L-CWAGKA, MCU38L-AWAGKA, MCU38L-CWAGKA
View related parts
Lexus RX330 Fuel Sender Gage Assembly
Part Number: 83320-48031
$102.49 MSRP: $136.38
You Save: $33.89 (25%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Gage Assy, Fuel Sender
- Replaced by: 83320-0E010
- Warranty: This genuine part is guaranteed by Lexus's factory warranty.
Fits the following Vehicles:
- 2004-2006 Lexus RX330 | STD | 6 Cyl 3.3L, 6 Cyl 3.5L | 2GRFE, 3MZFE; GSU30L-AWAGKA, GSU35L-AWAGKA, MCU33L-AWAGKA, MCU33L-CWAGKA, MCU38L-AWAGKA, MCU38L-CWAGKA

Lexus RX330 Fuel Level Sensor

The Lexus RX330 Fuel Level Sensor is the vehicle's built-in gauge brain that continuously informs the driver how much gasoline is left in the tank so that surprise empty tanks are avoided. Positioned inside the tank on every Lexus RX330, the Fuel Level Sensor is based on a buoyant float attached to an actuating rod that sweeps across a resistor, and the different electrical signal heads to the dashboard gauge for instant readouts. Earlier RX330 models shared a basic mechanical-electrical layout, but later Lexus editions use a fully electronic Fuel Level Sensor that is designed to withstand higher temperatures and relay information faster to the ECU while still retaining the basic float-rod-resistor layout. Whichever style is installed, the Fuel Level Sensor quickly corrects after each fill-up, preventing the annoying full reading that sticks with every sensor stick. A deteriorated Fuel Level Sensor can lead to frozen or wandering fuel gauge needles, so it pays to act fast and maintain the reliable Lexus RX330 fuel monitoring experience.

Should you need to purchase new auto parts for your vehicle, we strongly suggest you consider the genuine Lexus RX330 Fuel Level Sensor available on LexusPartsNow.com. Our OEM Lexus RX330 Fuel Level Sensor come with the reassurance of the manufacturer's warranty, a hassle-free return policy, and speedy delivery service, all at affordable prices online. Feel free to shop with confidence!

Lexus RX330 Fuel Level Sensor Parts Questions & Experts Answers

Fuel Sender Gage Assembly
83320-0E010
Q: How to remove and install a fuel pump and Fuel Level Sensor on Lexus RX330?
A:
Remove the rear seat. Pull the fuel pump/sending unit floor service hole cover off gently with a screwdriver. Lower fuel pressure and unscrew the fuel tank lid to empty. Twist and remove the fuel pump electricity wire connection by pulling up on the release button at its base, using pliers if you need to. Take off the black ground wire from the power battery. Take off the top fuel-supply line by removing the clip, pulling up, and checking the O-ring for damage before securing a replacement. For vehicles made before 2007, remove bolts holding the fuel pump and fuel level sensor assembly to its housing. Grasp the fuel pump/Fuel Level Sensor assembly from the fuel tank, with gentle tilting, to avoid hurting the fuel inlet strainer and sending unit float, loosening and moving the spring-type hose holder so you can disconnect the hose. First look at the strainer connected to the fuel pump's intake. Clean it with solvent and a brush if it's dirty. Get a new strainer when needed. Undoing the installation is just the reverse of undoing it.